GENI based Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)

The QUP v3 core is a GENI based AHB slave that provides a common data path
(an output FIFO and an input FIFO) for serial peripheral interface (SPI)
mini-core.

SPI in master mode supports up to 50MHz, up to four chip selects, programmable
data path from 4 bits to 32 bits and numerous protocol variants.

Required properties:
- compatible:	  Should contain "qcom,spi-geni"
- reg:		  Should contain base register location and length
- interrupts:	  Interrupt number used by this controller
- clocks:	  Should contain the core clock and the AHB clock.
- clock-names:	  Should be "core" for the core clock and "iface" for the
		  AHB clock.
- pinctrl-names:  Property should contain "default" and "sleep" for the
		  pin configurations during the usecase and during idle.
- pinctrl-x:	  phandle to the default/sleep pin configurations.
- #address-cells: Number of cells required to define a chip select
		  address on the SPI bus. Should be set to 1.
- #size-cells:	  Should be zero.
- spi-max-frequency: Specifies maximum SPI clock frequency,
		     Units - Hz. Definition as per
		     Documentation/devicetree/bindings/spi/spi-bus.txt
- qcom,wrapper-core: Wrapper QUPv3 core containing this SPI controller.

Optional properties:
- qcom,rt:	Specifies if the framework worker thread for this
		controller device should have "real-time" priority.
- qcom,disable-autosuspend: Specifies to disable runtime PM auto suspend.
- ssr-enable:	Required only for SSC QupV3 client for SSR notification.

SPI slave nodes must be children of the SPI master node and can contain
the following properties.

Required properties:
- compatible:     Should contain:
                  "qcom,spi-msm-codec-slave" for external codec control

- reg:            Chip select address of device.

- spi-max-frequency: Maximum SPI clocking speed of device in Hz.

Optional properties:
- spi-cpha:       Empty property indicating device requires
                  shifted clock phase (CPHA) mode.

- qcom,slv-ctrl : Set this flag to configure QUPV3 as SPI slave controller.

- qcom,disable-dma : Set this flag to ensure only fifo mode is used for
			transfers. FIFO mode does not work when FW of SE
			is configured in GSI mode.

- slv-cross-connected : Set this flag only when SPI-Slave MISO pin is connected
			to SPI-Master MOSI and vice-versa .

Other optional properties described in
Documentation/devicetree/bindings/spi/spi-bus.txt

Example:

	qupv3_spi10: spi@a84000 {
		compatible = "qcom,spi-geni";
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0xa84000 0x4000>;
		reg-names = "se_phys";
		clock-names = "se-clk", "m-ahb", "s-ahb";
		clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>,
			<&clock_gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
			<&clock_gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
		pinctrl-names = "default", "sleep";
		pinctrl-0 = <&qup_1_spi_2_active>;
		pinctrl-1 = <&qup_1_spi_2_sleep>;
		interrupts = <GIC_SPI 354 0>;
		spi-max-frequency = <19200000>;
		qcom,wrapper-core = <&qupv3_0>;

		dev@0 {
			compatible = "dummy,slave";
			reg = <0>;
			spi-max-frequency = <9600000>;
		};
	};
