#
# MMC core configuration
#
config PWRSEQ_EMMC
	tristate "HW reset support for eMMC"
	default y
	depends on OF
	help
	  This selects Hardware reset support aka pwrseq-emmc for eMMC
	  devices. By default this option is set to y.

	  This driver can also be built as a module. If so, the module
	  will be called pwrseq_emmc.

config PWRSEQ_SD8787
	tristate "HW reset support for SD8787 BT + Wifi module"
	depends on OF && (MWIFIEX || BT_MRVL_SDIO)
	help
	  This selects hardware reset support for the SD8787 BT + Wifi
	  module. By default this option is set to n.

	  This driver can also be built as a module. If so, the module
	  will be called pwrseq_sd8787.

config PWRSEQ_SIMPLE
	tristate "Simple HW reset support for MMC"
	default y
	depends on OF
	help
	  This selects simple hardware reset support aka pwrseq-simple for MMC
	  devices. By default this option is set to y.

	  This driver can also be built as a module. If so, the module
	  will be called pwrseq_simple.

config MMC_BLOCK
	tristate "MMC block device driver"
	depends on BLOCK
	default y
	help
	  Say Y here to enable the MMC block device driver support.
	  This provides a block device driver, which you can use to
	  mount the filesystem. Almost everyone wishing MMC support
	  should say Y or M here.

config MMC_BLOCK_MINORS
	int "Number of minors per block device"
	depends on MMC_BLOCK
	range 4 256
	default 8
	help
	  Number of minors per block device. One is needed for every
	  partition on the disk (plus one for the whole disk).

	  Number of total MMC minors available is 256, so your number
	  of supported block devices will be limited to 256 divided
	  by this number.

	  Default is 8 to be backwards compatible with previous
	  hardwired device numbering.

	  If unsure, say 8 here.

config MMC_BLOCK_DEFERRED_RESUME
	bool "Defer MMC layer resume until I/O is requested"
	depends on MMC_BLOCK
	default n
	help
	  Say Y here to enable deferred MMC resume until I/O
	  is requested.

	  This will reduce overall resume latency and
	  save power when there is an SD card inserted but not being used.

config SDIO_UART
	tristate "SDIO UART/GPS class support"
	depends on TTY
	help
	  SDIO function driver for SDIO cards that implements the UART
	  class, as well as the GPS class which appears like a UART.

config MMC_TEST
	tristate "MMC host test driver"
	help
	  Development driver that performs a series of reads and writes
	  to a memory card in order to expose certain well known bugs
	  in host controllers. The tests are executed by writing to the
	  "test" file in debugfs under each card. Note that whatever is
	  on your card will be overwritten by these tests.

	  This driver is only of interest to those developing or
	  testing a host driver. Most people should say N here.

config MMC_RING_BUFFER
	bool "MMC_RING_BUFFER"
	depends on MMC
	default n
	help
	  This enables the ring buffer tracing of significant
	  events for mmc driver to provide command history for
	  debugging purpose.

	  If unsure, say N.

config MMC_EMBEDDED_SDIO
	boolean "MMC embedded SDIO device support"
	help
	  If you say Y here, support will be added for embedded SDIO
	  devices which do not contain the necessary enumeration
	  support in hardware to be properly detected.

config MMC_PARANOID_SD_INIT
	bool "Enable paranoid SD card initialization"
	help
	  If you say Y here, the MMC layer will be extra paranoid
	  about re-trying SD init requests. This can be a useful
	  work-around for buggy controllers and hardware. Enable
	  if you are experiencing issues with SD detection.

config MMC_CLKGATE
	bool "MMC host clock gating"
	help
	  This will attempt to aggressively gate the clock to the MMC card.
	  This is done to save power due to gating off the logic and bus
	  noise when the MMC card is not in use. Your host driver has to
	  support handling this in order for it to be of any use.

	  If unsure, say N.

config MMC_SIMULATE_MAX_SPEED
	bool "Turn on maximum speed control per block device"
	depends on MMC_BLOCK
	help
	  Say Y here to enable MMC device speed limiting. Used to test and
	  simulate the behavior of the system when confronted with a slow MMC.

	  Enables max_read_speed, max_write_speed and cache_size attributes to
	  control the write or read maximum KB/second speed behaviors.

	  If unsure, say N here.
